STAUF USA Adhesive to glue down wood flooring and floor covering | Product Listing STAUF
Menu

PDF version

Technical Data Sheet (TDS)

M400 Endura-Tec

Quick Setting Repair & Mounting Adhesive

Special features

  • Timber Flooring Repairs
  • Repairs of Synthetic Turf Seams
  • Molding Installation
  • Cove Base Installation
  • Stair Tread Installation

Product Description
M400 is a repair adhesive for synthetic turf installations, whether it is over seaming tape or full spread.
Pre-Installation Checklist
A successful installation requires proper preparation of the sub floor. Read and understand all applicable guidelines and technical data sheets before beginning installation. Follow industry standards and flooring manufacturer's recommendations for sub floor preparation, design, layout and application of flooring materials.
Sub Floor Examination
Prior to processing, the sub floor must be checked according to national standards. It must be solid and sound, level, free of indentations as well as resistant to pressure and tension.
Installation Procedure
Spread adhesive using a caulking gun. Install material immediately and press down firmly.
Limitations
In case of accident, injury, spill or exposure, see MSDS sheet for information. Consult technical data sheet at www.staufusa.com for updated information.
The foregoing representations are based on the results of our most current product and material testing within a controlled environment and are of a non-obligatory advisory nature only. As such, they do not constitute an express or implied warranty of any kind including the Warranty of Merchantability and/or Fitness for a Particular Purpose. Because we have no control over the actual quality of workmanship, materials used and worksite conditions, STAUF USA Adhesive LLC, will in no event be liable for any incidental and/or consequential damages. Therefore, we strongly recommend that prior on-site testing be conducted to refer to and study the suitability of the product for the intended purpose. With the release of this technical information sheet all its prior versions become invalid. For warranty and warranty disclaimer information please see our Limited Lifetime Warranty @ www.staufusa.com
General Features
  • moisture cured urethane
  • LEED qualified
  • contains no water
  • contains no solvents
  • contains no VOC
  • nonflammable
  • high solids content
  • Isocyanate based Urethane for strong bond
  • Freeze/thaw stable
Installation Features
  • grabs quicker, less slippage
  • wet lay - no flash time required
  • superior green grab
  • bridges normal sub floor variations
  • very low odour
  • cleans with acetone
  • dries quickly
  • higher temp & RH will shorten drying time
Long Term Features
  • resistant against aging
  • remains elastic
  • suitable for radiant heat systems
  • adhesive is waterproof when cured
  • Eliminates hollow spots
Approved Materials
  • Engineered Timber Flooring
  • Ceramic & Stone
  • Synthetic Turf
  • Sports Flooring
  • Vinyl Tiles and Planks (VCT, LVT, SVT, LVP)
  • Rubber Flooring
  • Wall coverings
  • Wall/Cove base
  • Strip Flooring (Solid Timber, <6 cm wide)
  • Shorts (Solid Timber, <6 cm wide, <1 m long)
  • Planks (Solid Timber, <18 cm wide)
  • Parquet
  • Bamboo Flooring (except Stranded Bamboo)
  • Laminate Flooring
Approved Substrates
  • Concrete Slabs
  • OSB (underlayment grade)
  • plywood (underlayment grade)
  • ceramic tiles
  • stone, terrazzo
  • cured levelling compounds
  • radiant heated sub floors
  • Seaming Tape
  • Metal Floors
  • Asphalt
  • Epoxy Sealers (100% solid, cured)
  • Drywall
  • Plaster
Cure Time until Normal Traffic
  • approx. 30 mins.
Clean-Up
  • Use STAUF UCL-QT while wet
Temperature Range during Installation
  • 10 – 40 °C
Relative Humidity Range during Installation
  • 20% - 90%
Packaging Size
  • No translation available
  • 30 count case
colour
  • Grey
VOC (calculated) [g/L]
  • 0 g/L
Storage
  • dry
Shelf Life
  • 12 Months in original, unopened container
Open Time30% R/H50% R/H80% R/H
50�F/10�C25 mins 20 mins 15 mins 
70�F/21�C20 mins 15 mins 10 mins 
90�F/32�C15 mins 10 mins 5 mins 
Revision: 2014-07-17 12:27:39

Please enter the email address of the person to whom you would like to send this PDF.